How To Bind Off In Crochet

Download Article

Download Commodity

When you come to the end of a crochet projection y'all need to tie it off properly or all of your hard work could come up undone. The term "bind off" is used to describe how you tie off your crocheting properly, making a seamless transition at the end of your project. When your crochet pattern asks you to "bind off", here is what you should do.

1. 

   ane

   End the stitches on your last row. You should end up with i loop on your hook and the working end of your yarn sticking out across the last sew together.

2. 

   2

   Make one additional concatenation sew. Brainstorm this by looping the working stop of your yarn around your claw. Rotate your hook slightly, and then the yarn stays on it, and then pull the loop of yarn dorsum through the loop that was already on your hook. You should now have i new loop on your hook.

   Advertisement

3. 

   3

   Pull the loop off your hook and pull information technology out a bit, extending it upwardly about three inches. You can exercise this by pulling the actress yarn from the working end of your project.

4. 

   4

   Clip the middle of the loop with your scissors. Pull out the loose end of the yarn (your working terminate), leaving one slice of yarn sticking out of the end of your project. This piece should exist at least a couple inches long.

5. 5

   Pull the slice of yarn sticking out of your projection taut. ^[one] This should necktie the end of the projection off permanently and finer, creating a solid knot.

6. 

   6

   Thread the end of the yarn onto a yarn needle. If yous are having a hard fourth dimension doing this, but curve the middle of the yarn in half and squeeze it tight. Push the aptitude area through the eye of the needle.

7. 

   7

   Thread the end of the yarn back through your projection so it is hidden. Using the needle, pull the yarn back through the center of the concluding three stitches y'all made. Pull the end of the yarn out, so that the needle and yarn are sticking out in the middle of the row, and so stick the needle back into the project. Head dorsum in the other management with your needle and yarn, inserting the needle one row down and pushing information technology through the centre of most three stitches. This should lock your yarn tail in place.

8. 

   8

   Trim any excess yarn one time you have threaded the yarn back and forth through the end of your project. The yarn should stay in place, subconscious in the center of several rows of your stitches.

9. 

   ix

   Stretch out the concluding row of your project. Make sure that the cease of the yarn is still tucked away neatly and that the tension on the row is that aforementioned as the residuum of your project. Your project is now finished!

Advert

1. 

   one

   Crochet your concluding ring of stitches. This will leave you with a gap between the beginning of the circular of stitches and the end of that round.

2. 

   2

   Pull the concluding loop of yarn off your hook and extend information technology out, pulling excess yarn from the working end of your yarn. You should make your loop about eight inches long.

3. 

   3

   Cutting the middle of the yarn loop with your scissors. Pull the working end out of the projection, leaving one piece of yarn sticking out of the end of your round. You will end up with iv or five inches of tail, which is necessary for y'all to be able to finish the projection.

4. 

   4

   Thread a yarn or tapestry needle onto the end of your yarn tail. If you are having a difficult time getting the yarn threaded, curve your piece of yarn over and squeeze the bent surface area as thin as possible with your thumb and forefinger. Push this thin aptitude area through the head of the needle. It should go through easier than a raggedy end piece.

5. 

   five

   Insert the needle under the outset stitch of the circular, moving from exterior to inside, then pull your yarn tight. In essence, you are connecting the cease of your terminal circular to the beginning of your concluding round by replicating that same type of stitch.^[2]

6. 

   6

   Take your needle and pull it back toward the stop of your round, inserting it into the eye of your terminal bound off run up, the one at the very end of your final row. Point the cease of the needle toward the inside of your projection and pull the thread through. This should lock the end of your yarn in place for good.

   • Try to match the tension that y'all used in the rest of the projection, then that the concluding stitch you just fabricated does not stand out.^[three]

7. 

   seven

   Weave in the tail of your yarn on the inside of your projection. Brand sure that the end is secure before you lot clip off whatsoever extra tail with your pair of scissors. You should now have an invisible demark off on your circular crochet project!

Advertisement

Inquire a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Advertizement

Thanks for submitting a tip for review!

Things You'll Demand

• Crochet hook
• Yarn
• Scissors

About This Article

Cheers to all authors for creating a folio that has been read 85,108 times.

Did this article assist you?

Source: https://www.wikihow.com/Bind-Off-(Crocheting)

Share this post